Last Updated 2nd of May, 2010
What must I check during pre trip inspection for my NC CDL test? North Carolina
NC CDL Test Inspection ChecklistThe driving test consists of three parts: the pre trip inspection, basic driving skills, and the road test.
Every CDL driver must pass the inspection first. During this portion of the of the CDL test you'll need to identify specific parts and explain what you're looking for to the examiner. You'll be expected to cover the following:
Engine Compartment (Engine Off)
Leaks and Hoses:
- Look for puddles on the ground.
- Look for dripping fluids on the underside of the engine and transmission.
- Check hoses for leaks.
- Point out where dipstick is located.
- Make sure oil level is adequate.
- Check the coolant level.
- Indicate where dipstick is located.
- Check the power steering fluid level.
- Check the power steering, water pump, alternator, and air compressor belts for snugness, cracks, or fraying.
Cab Check (Engine On)
- Depress the clutch.
- Place the gearshift lever in neutral.
- Start engine and release clutch slowly.
- Make sure the gauge is functioning.
- Check that the pressure gauge shows increasing or normal oil pressure, or that the warning light goes off.
- Check that the gauge is working properly.
- The temperature should gradually climb to a normal operating range, or the temperature light should be off.
- Make sure the gauges show the alternator and/or generator is charging or that the warning light is off.
- Make sure the gauge is functioning properly.
- Mirrors should be clean and adjusted properly.
- Windshield should be free of cracks and unnecessary decals.
- Check for spare electrical fuses.
- Check for three emergency triangles.
- Check fire extinguisher.
- Non-power steering: check for excessive play.
- Power steering: check for excessive play with the engine running.
- Check that the wiper arms and blades are secure and free of damage.
- If equipped, windshield wipers must operate properly.
- Make sure the turn signals, four-way emergency flashers, and high beam indicator lights work on the dashboard.
- Check that horn works properly.
- Make sure headlights, directional lights, taillights, clearance, four-way flashers, brake lights, and red and amber reflectors are all clean and functioning.
Parking Brake Check:
- Apply parking brake and make sure it holds by shifting into lower gear and slowly pulling against it.
- With engine running, apply pressure to brake pedal and hold for five seconds, making sure the brake pedal does not move.
- Make sure the warning buzzer and/or light is off.
- Check the brake operation by moving slowly forward and hitting the brake, paying attention to any pulling or delay.
- Test air leakage rate.
- Test air brake system for leaks.
- Check that spring brakes come on automatically.
- Check rate of air pressure buildup.
- Check service brakes.
- Check that the steering box is mounted and secure.
- Look for steering fluid leaks.
- Check that the connecting links, arms, and rods from the steering box to the wheel are not worn or cracked.
- Make sure the joints and sockets are not worn or loose.
- Look for broken or cracked leaf springs.
- Look for broken or bent coil springs.
- Check air ride suspension for damage and leaks.
- Check for cracked or broken spring hangers, missing or damaged bushings, and broken or missing axle mounting parts.
- Check that shocks are secure and without leaks.
- Check for broken or missing parts.
- When pulled by hand, the brake rod should not move more than an inch.
- Brake chambers should not be leaking, cracked, or dented.
- Check for cracked, leaking, or worn hoses.
- Check for cracks, dents, or holes.
- Brake linings or pads (where visible) should not be worn or excessively thin.
- Look for damaged or bent rims.
- Check for tread depth.
- Look for cuts or damage to tread or sidewalls.
- Make sure stems are not missing, broken, or damaged.
- Check for proper inflation.
- Make sure grease and axle seals aren't leaking.
- Make sure all lug nuts are accounted for, free of cracks, and securely fastened.
Side of Vehicle
Door(s) and Mirror(s):
- Check that doors are not damaged and can be opened properly.
- Make sure mirror and mirror brackets are secure.
- Check that tanks are secure, caps are tight, and there are no visible leaks.
- Check that the battery is secure and connections are tight.
- Make sure the battery is free of corrosion.
- Check that battery box and cover or door is secure.
- Check that the drive shaft is not bent or cracked.
- Make sure the couplings are secure and free of foreign objects.
- Check system for damage and signs of leaks.
- Check that the system is connected and mounted properly.
- Check for cracks, broken welds, holes, or other damage to the longitudinal frame members, cross members, box, and floor.
Rear of Vehicle
- If equipped, make sure splash guards are not damaged and mounted properly.
- Make sure the doors and hinges are not damaged and all work properly.
- Ties, straps, and binders must all be secure.
- If equipped with a cargo lift, check for leaking and damaged parts.
- Listen for air leaks.
- Make sure air and electrical lines are not tangled, pinched, or dragging against tractor parts.
- Check that the catwalk is solid, free of objects, and securely bolted to tractor frame.
- Check for loose or missing mounting brackets, clamps, bolts, or nuts.
- Both the fifth wheel and slide mounting must be solidly attached.
- Look into fifth wheel gap and check that locking jaws are fully closed around the kingpin.
- Check for brakes or cracks in the platform structure which supports the fifth wheel skid plate.
- Make sure the kingpin is not bent.
- Make sure the visible part of the apron is not bent, cracked, or broken.
- Check that the trailer is laying flat on the fifth wheel skid plate.
- If equipped, look for loose or missing pins in the slide mechanism of the fifth wheel.
- Make sure locking pins are fully engaged.
- Check that the fifth wheel is positioned properly so the tractor frame will clear the landing gear and the tractor will not strike the trailer during turns.
Obtain CDL Practice Before the Driving TestBefore making an appointment for the NC driving test, take at least one CDL practice test - no matter what CDL class you're applying for. These can be found online. When you're ready for the actual test, the final hurdle for obtaining a commercial license, contact the North Carolina DMV for a test date.
If you have any questions about the test process, consult the North Carolina CDL manual.
No visitor comments posted. Post a comment
Post Comment for "What must I check during pre trip inspection for my NC CDL test?"
To post a comment for this article, simply complete the form below. Fields marked with an asterisk are required.
No users have voted.
How would you rate this answer?
Thank you for rating this answer.